Projects
There are 9 results.
AQUASENSE - Research and Validation of a Prototype for Simultaneous LWC/IWC Detection in Icing Wind Tunnels
Within the AquaSense framework, a method for the simultaneous detection of both the aggregation state and concentration of water in flowing media, specifically for application in high temporal resolution icing wind tunnels, will be investigated for the first time in order to test, optimise and certify aircraft systems under defined icing conditions. A photoacoustic spectroscopy based prototype will be developed and tested under different operating conditions in the RTA Icing Wind Tunnel and the FHJ Icing Wind Tunnel.
AntiIce - Anti-icing/De-icing Systems to Improve Aircraft Performance and Safety
The aim of the Anti-Ice project was the production of new and innovative materials for aircraft surface coating to prevent icing. Furthermore, micromechanical (piezo) actuators for active ice removal have been developed.
HEAT - Heating Paint Based De-icing System for Drive Components and Aircraft Wings
The aim of the HEAT project was to develop a special heating paint as the basis for a lightweight, simple and flexible de-icing system for aircraft. This de-icing system, which is intended for both anti-icing and de-icing procedures, is intended to increase the safety of the aircraft through high damage tolerance and, at the same time, to be particularly energy-saving due to the lower system weight and efficient energy conversion.
Ice Grid - Investigation of Ice Formation on Protection Grids in Aircraft Air-Conditioning Systems
The IceGrid project examined protection grids in the air conditioning systems of passenger aircraft and at the interface to mobile climate modules on the ground for icing and de-icing. The methods used included both experimental testing in the icing wind tunnel and numerical simulations.
IceDrip - Aircraft Anti-icing and De-icing through Assemblies of Conducting Varnish and Functional Coatings
In the project IceDrip the rather promising concept of a discontinuous, electro-thermal de-icer is being investigated. The main aim of the present project is to significantly increase the already existing energetic advantages of the discontinuous de-icer by means of surface-active coatings, in order to achieve a performance range which would make the system suitable for general aviation aircraft, as well as smaller aircraft, which are equipped as large aircraft.
MIXVAL - Mixer Simulation and Validation
In passenger aircraft, the mixing and distribution of humid airflow from the cabin and engines into the cockpit and passenger cabin, as well as electronic components, takes place at a central location of the air conditioning system, the mixer. So far, the flow and heat transfer processes and the ice formation and accretion cannot be calculated with sufficient accuracy. Therefore, the aim of this project is to develop a method for simulating the physical processes in the mixer.
TWID - Heating-Paint Sensor Based Wing Ice Detector
In the scope of the TWID project, a method for reliable detection of ice on wing surfaces and other relevant structures on an aircraft is to be developed, examined and validated in the course of various tests on the small-scale and full-scale models in the icing wind tunnel. Ice detection combined with the de-icing method, which is already in development, results in a completely self-sufficient de-icing system, which independently identifies and reliably removes ice on the wings.
VertSLD - Prospecting for the Construction of a Vertical Icing Wind Tunnel for Experimental Simulation of Icing by Supercooled Large Droplets
The exploratory project VertSLD investigates both the physical feasibility and economic viability of an icing wind tunnel concept which avoids many of the difficulties that arise in existing icing wind tunnels when the size of the water droplets exceeds a few hundred microns. in this new concept the "flight path" of the drops within which they are supercooled is arranged vertically and not horizontally.
eWING_DE-ICER - Development of an Energy-Efficient Electrothermal De-icing System for Wing Leading Edges in Aviation
Within the scope of the eWING_DE-ICER project, a method for developing energy-optimised de-icing systems for wing leading edges, based on a thermoelectric heating system, is to be developed. In addition to the development of forecasting models for the optimal design of all components involved, different prototypes are to be set up as in the model, as well as in full-scale, and tested in various icing wind tunnels.